---

Jeg har anskaffet en Samsung (YP-K3) mp3-afspiller, som jeg ikke kan få
til at virke i ubuntu. den kan køre på husets anden pc (WinXP) og virker
helt der.
Min ubuntu kan ikke se den overhovedet.
Kan nogen her hjælpe?
Hans

---

Den Wed, 09 Jan 2008 23:12:43 +0100 skrev Hans Houmøller:

> Jeg har anskaffet en Samsung (YP-K3) mp3-afspiller, som jeg ikke kan få
> til at virke i ubuntu. den kan køre på husets anden pc (WinXP) og virker
> helt der.
> Min ubuntu kan ikke se den overhovedet. Kan nogen her hjælpe?
> Hans

USB, Bluetooth eller hvad? Ubuntu popper da ellers op med "Lagerenhed"
til ligemeget hvad på USB.

--
Med venlig hilsen
Karl Erik Christensen

---

Det er usb, og det undrer også mig, at den ikke opdager den ny enhed -
det plejer at ske!
Hans

---

Når jeg sætter den i et usb-stik, tænder mp3'en og viser, at den er
fuldt opladet, men så sker der ikke mere.
Som sagt kører den ok på husets anden pc med WinXP. På denne pc, der
både har WinXP og ubuntu virker hverken i det ene eller det andet
styresystem.
Hans

---

Den Wed, 09 Jan 2008 23:26:28 +0100 skrev Hans Houmøller:
> Det er usb, og det undrer også mig, at den ikke opdager den ny enhed -
> det plejer at ske!
> Hans

Hvad siger lsusb?

Mvh
Kent
--
"So there I was surrounded by all these scary creatures
They were even scarier than what Microsoft call features"
- C64Mafia: Forbidden Forest (Don't Go Walking Slow).

---

Her er hvad lsusb siger:

Bus 005 Device 001: ID 0000:0000
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 002: ID 046d:c518 Logitech, Inc.
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 004: ID 04e8:5081 Samsung Electronics Co., Ltd
Bus 002 Device 003: ID 058f:9254 Alcor Micro Corp. Hub
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

---

Den Thu, 10 Jan 2008 19:22:07 +0100 skrev Hans Houmøller:
> Her er hvad lsusb siger:
>
> Bus 002 Device 004: ID 04e8:5081 Samsung Electronics Co., Ltd

Så prøv:

lsusb -d 04e8:5081 -v | grep -i class

Mvh
Kent
--
"So there I was surrounded by all these scary creatures
They were even scarier than what Microsoft call features"
- C64Mafia: Forbidden Forest (Don't Go Walking Slow).

---

Det giver:

hans@hans-desktop$ sudo lsusb -d 04e8:5081 -v | grep -i class
can't get debug descriptor: Connection timed out
cannot read device status, Connection timed out (110)
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0

---

Den Thu, 10 Jan 2008 19:47:06 +0100 skrev Hans Houmøller:
> Det giver:
>
> hans@hans-desktop$ sudo lsusb -d 04e8:5081 -v | grep -i class
>
> bInterfaceClass 255 Vendor Specific Class
> bInterfaceSubClass 255 Vendor Specific Subclass

En standard mass storage MP3-afspiller giver:

bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI

"Vendor Specific" betyder at der skal bruges en speciel driver, i
modsætning til "Mass Storage" der betyder at det bare virker.

Prøv at bruge lidt tid på
http://www.google.com/search?q=usb+04e8%3A5081+linux&btnG=Search

Mvh
Kent
--
"So there I was surrounded by all these scary creatures
They were even scarier than what Microsoft call features"
- C64Mafia: Forbidden Forest (Don't Go Walking Slow).

---

On 2008-01-10, Kent Friis <nospam@nospam.invalid> wrote:
>
> "Vendor Specific" betyder at der skal bruges en speciel driver, i
> modsætning til "Mass Storage" der betyder at det bare virker.

Det er kun en halv sandhed. Jeg har en ældre Samsung, der optræder som
et mass storage device, men man skal desværre lige have noget software,
der kan bygge et index på den før man kan vælge musikken.

--
Andreas

---

Den Thu, 10 Jan 2008 19:36:34 +0000 (UTC) skrev Andreas Plesner Jacobsen:
> On 2008-01-10, Kent Friis <nospam@nospam.invalid> wrote:
>>
>> "Vendor Specific" betyder at der skal bruges en speciel driver, i
>> modsætning til "Mass Storage" der betyder at det bare virker.
>
> Det er kun en halv sandhed. Jeg har en ældre Samsung, der optræder som
> et mass storage device, men man skal desværre lige have noget software,
> der kan bygge et index på den før man kan vælge musikken.

Er der ikke noget med at iPod har samme problem? Anyway, så virker
det jo netop - som mass storage. Man kan jo stadig bruge den til
at overføre filer.

(Jeg har fx et par ssh keys på min MP3-afspiller. Det er det nemmeste
sted at have den slags, når man skal logge ind fra remote).

Mvh
Kent
--
"So there I was surrounded by all these scary creatures
They were even scarier than what Microsoft call features"
- C64Mafia: Forbidden Forest (Don't Go Walking Slow).

---

Karl Erik Christensen skrev:
> Den Wed, 09 Jan 2008 23:12:43 +0100 skrev Hans Houmøller:
>
>> Jeg har anskaffet en Samsung (YP-K3) mp3-afspiller, som jeg ikke kan få
>> til at virke i ubuntu. den kan køre på husets anden pc (WinXP) og virker
>> helt der.
>> Min ubuntu kan ikke se den overhovedet. Kan nogen her hjælpe?
>> Hans
>
> USB, Bluetooth eller hvad? Ubuntu popper da ellers op med "Lagerenhed"
> til ligemeget hvad på USB.
>

Når jeg bruger USB Viewer, kan ubuntu se, at der er en Samsung YP-K3
afspiller, MEN jeg kan ikke finde ud af at mounte den.
En "sudo mount" kommando giver dette:
hans@hans-desktop$ sudo mount
/dev/sdb1 on / type ext3 (rw,errors=remount-ro)
proc on /proc type proc (rw,noexec,nosuid,nodev)
/sys on /sys type sysfs (rw,noexec,nosuid,nodev)
varrun on /var/run type tmpfs (rw,noexec,nosuid,nodev,mode=0755)
varlock on /var/lock type tmpfs (rw,noexec,nosuid,nodev,mode=1777)
procbususb on /proc/bus/usb type usbfs (rw)
udev on /dev type tmpfs (rw,mode=0755)
devshm on /dev/shm type tmpfs (rw)
devpts on /dev/pts type devpts (rw,gid=5,mode=620)
lrm on /lib/modules/2.6.20-16-generic/volatile type tmpfs (rw)
/dev/sda1 on /media/hda1 type ntfs (rw,nls=utf8,umask=007,gid=46)
/dev/sda5 on /media/hda5 type vfat (rw,utf8,umask=007,gid=46)
binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw)
procbususb on /proc/bus/usb type usbfs (rw)

Hvad skal jeg gøre så?
Hans

---

Den Wed, 16 Jan 2008 17:20:59 +0100 skrev Hans Houmøller:
> Karl Erik Christensen skrev:
>> Den Wed, 09 Jan 2008 23:12:43 +0100 skrev Hans Houmøller:
>>
>>> Jeg har anskaffet en Samsung (YP-K3) mp3-afspiller, som jeg ikke kan få
>>> til at virke i ubuntu. den kan køre på husets anden pc (WinXP) og virker
>>> helt der.
>>> Min ubuntu kan ikke se den overhovedet. Kan nogen her hjælpe?
>>> Hans
>>
>> USB, Bluetooth eller hvad? Ubuntu popper da ellers op med "Lagerenhed"
>> til ligemeget hvad på USB.
>
> Når jeg bruger USB Viewer, kan ubuntu se, at der er en Samsung YP-K3
> afspiller, MEN jeg kan ikke finde ud af at mounte den.

Fandt du en driver?

Mvh
Kent
--
"So there I was surrounded by all these scary creatures
They were even scarier than what Microsoft call features"
- C64Mafia: Forbidden Forest (Don't Go Walking Slow).

---

Den Wed, 09 Jan 2008 23:40:30 +0100 skrev Hans Houmøller:

> Når jeg sætter den i et usb-stik, tænder mp3'en og viser, at den er
> fuldt opladet, men så sker der ikke mere. Som sagt kører den ok på
> husets anden pc med WinXP. På denne pc, der både har WinXP og ubuntu
> virker hverken i det ene eller det andet styresystem.
> Hans

Jamen så var det jo nok værd at undersøge om usb porten virker. Hvad sker
når du kører WinXP på samme maskine?

--
Med venlig hilsen
Karl Erik Christensen

---

Hans Houmøller wrote:

> Jeg har anskaffet en Samsung (YP-K3) mp3-afspiller, som jeg ikke kan få
> til at virke i ubuntu. den kan køre på husets anden pc (WinXP) og virker
> helt der.
> Min ubuntu kan ikke se den overhovedet.
> Kan nogen her hjælpe?

Hvad siger lsudb og dmesg? En grim måde, der måske kan hjælpe er at køre
killall hald som root og prøve igen. Så vil den dog ikke selv poppe op, men
du vil kunne se den med lsusb og dmesg. Jeg har været ude for en USB
lagerenhed der ikke kunne sammen med HAL og crashede når den blev
tilsluttet. Genstart maskinen bagefter, så du er sikker på at virker som
det skal.

--
Lasse Jensen [fafler at g mail dot com]
Linux, the choice of a GNU generation.

---

Her er hvad de to commandoer siger:


hans@hans-desktop$ sudo lsusb
Password:
Bus 008 Device 001: ID 0000:0000
Bus 007 Device 001: ID 0000:0000
Bus 006 Device 003: ID 04e8:5081 Samsung Electronics Co., Ltd
Bus 006 Device 002: ID 058f:9254 Alcor Micro Corp. Hub
Bus 006 Device 001: ID 0000:0000
Bus 005 Device 001: ID 0000:0000
Bus 004 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Bus 003 Device 004: ID 046d:c518 Logitech, Inc.
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
hans@hans-desktop$ sudo lsubd
sudo: lsubd: command not found
hans@hans-desktop$ lsudb
bash: lsudb: command not found
hans@hans-desktop$ lsusbd
bash: lsusbd: command not found
hans@hans-desktop$ dmesg
[17179569.184000] Linux version 2.6.17-12-generic (root@terranova) (gcc
version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 SMP Tue
Dec 18 02:12:38 UTC 2007 (Ubuntu 2.6.17-12.42-generic)
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[17179569.184000] BIOS-e820: 0000000000100000 - 000000005f740000 (usable)
[17179569.184000] BIOS-e820: 000000005f740000 - 000000005f750000 (ACPI
data)
[17179569.184000] BIOS-e820: 000000005f750000 - 000000005f800000 (ACPI NVS)
[17179569.184000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[17179569.184000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000] BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved)
[17179569.184000] 631MB HIGHMEM available.
[17179569.184000] 896MB LOWMEM available.
[17179569.184000] On node 0 totalpages: 390976
[17179569.184000] DMA zone: 4096 pages, LIFO batch:0
[17179569.184000] Normal zone: 225280 pages, LIFO batch:31
[17179569.184000] HighMem zone: 161600 pages, LIFO batch:31
[17179569.184000] DMI present.
[17179569.184000] ACPI: RSDP (v000 ACPIAM
) @ 0x000fa560
[17179569.184000] ACPI: RSDT (v001 A M I OEMRSDT 0x08000616 MSFT
0x00000097) @ 0x5f740000
[17179569.184000] ACPI: FADT (v002 A M I OEMFACP 0x08000616 MSFT
0x00000097) @ 0x5f740200
[17179569.184000] ACPI: MADT (v001 A M I OEMAPIC 0x08000616 MSFT
0x00000097) @ 0x5f740300
[17179569.184000] ACPI: OEMB (v001 A M I OEMBIOS 0x08000616 MSFT
0x00000097) @ 0x5f750040
[17179569.184000] ACPI: DSDT (v001 75i6G 75i6G253 0x00000253 INTL
0x02002026) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x808
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 15:4 APIC version 20
[17179569.184000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[17179569.184000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[17179569.184000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[17179569.184000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000,
GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high
level)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] Enabling APIC mode: Flat. Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 60000000 (gap:
5f800000:9f500000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hdc6 ro quiet splash
locale=da_DK
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Enabling unmasked SIMD FPU exception support... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[17179569.184000] Detected 2797.003 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179569.736000] Dentry cache hash table entries: 131072 (order: 7,
524288 bytes)
[17179569.736000] Inode-cache hash table entries: 65536 (order: 6,
262144 bytes)
[17179569.788000] Memory: 1540356k/1563904k available (1911k kernel
code, 22148k reserved, 1073k data, 308k init, 646400k highmem)
[17179569.788000] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[17179569.868000] Calibrating delay using timer specific routine..
5598.88 BogoMIPS (lpj=11197765)
[17179569.868000] Security Framework v1.0.0 initialized
[17179569.868000] SELinux: Disabled at boot.
[17179569.868000] Mount-cache hash table entries: 512
[17179569.868000] CPU: After generic identify, caps: bfebfbff 20000000
00000000 00000000 0000651d 00000000 00000001
[17179569.868000] CPU: After vendor identify, caps: bfebfbff 20000000
00000000 00000000 0000651d 00000000 00000001
[17179569.868000] monitor/mwait feature present.
[17179569.868000] using mwait in idle threads.
[17179569.868000] CPU: Trace cache: 12K uops, L1 D cache: 16K
[17179569.868000] CPU: L2 cache: 256K
[17179569.868000] CPU: Hyper-Threading is disabled
[17179569.868000] CPU: After all inits, caps: bfebfbff 20000000 00000000
00000180 0000651d 00000000 00000001
[17179569.868000] Checking 'hlt' instruction... OK.
[17179569.884000] SMP alternatives: switching to UP code
[17179569.884000] Freeing SMP alternatives: 16k freed
[17179569.884000] checking if image is initramfs... it is
[17179570.352000] Freeing initrd memory: 5327k freed
[17179570.352000] ACPI: Core revision 20060707
[17179570.352000] ACPI: Looking for DSDT ... not found!
[17179570.356000] CPU0: Intel(R) Celeron(R) CPU 2.80GHz stepping 09
[17179570.356000] Total of 1 processors activated (5598.88 BogoMIPS).
[17179570.356000] ENABLING IO-APIC IRQs
[17179570.356000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179570.500000] Brought up 1 CPUs
[17179570.500000] migration_cost=0
[17179570.500000] NET: Registered protocol family 16
[17179570.500000] EISA bus registered
[17179570.500000] ACPI: bus type pci registered
[17179570.500000] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
[17179570.500000] PCI: Using configuration type 1
[17179570.500000] Setting up standard PCI resources
[17179570.512000] ACPI: Interpreter enabled
[17179570.512000] ACPI: Using IOAPIC for interrupt routing
[17179570.512000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179570.512000] PCI: Probing PCI hardware (bus 00)
[17179570.516000] Boot video device is 0000:00:02.0
[17179570.516000] PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
[17179570.516000] PCI quirk: region 0480-04bf claimed by ICH4 GPIO
[17179570.516000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[17179570.516000] PCI: Transparent bridge - 0000:00:1e.0
[17179570.516000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179570.516000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[17179570.524000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11
12 14 15)
[17179570.524000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11
12 14 15)
[17179570.524000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11
12 14 15)
[17179570.524000] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11
12 14 15)
[17179570.524000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11
12 14 15) *0, disabled.
[17179570.524000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11
12 14 15)
[17179570.528000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11
12 14 15)
[17179570.528000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11
12 14 15)
[17179570.528000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179570.528000] pnp: PnP ACPI init
[17179570.532000] pnp: PnP ACPI: found 13 devices
[17179570.532000] PnPBIOS: Disabled by ACPI PNP
[17179570.532000] PCI: Using ACPI for IRQ routing
[17179570.532000] PCI: If a device doesn't work, try "pci=routeirq". If
it helps, post a report
[17179570.536000] pnp: 00:0b: ioport range 0x290-0x29f has been reserved
[17179570.536000] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
[17179570.536000] PCI: Bridge: 0000:00:1e.0
[17179570.536000] IO window: b000-bfff
[17179570.536000] MEM window: ff000000-ff0fffff
[17179570.536000] PREFETCH window: disabled.
[17179570.536000] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[17179570.536000] NET: Registered protocol family 2
[17179570.576000] IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
[17179570.576000] TCP established hash table entries: 262144 (order: 9,
2097152 bytes)
[17179570.576000] TCP bind hash table entries: 65536 (order: 7, 524288
bytes)
[17179570.576000] TCP: Hash tables configured (established 262144 bind
65536)
[17179570.576000] TCP reno registered
[17179570.580000] audit: initializing netlink socket (disabled)
[17179570.580000] audit(1199993184.580:1): initialized
[17179570.580000] highmem bounce pool size: 64 pages
[17179570.580000] VFS: Disk quotas dquot_6.5.1
[17179570.580000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179570.580000] Initializing Cryptographic API
[17179570.580000] io scheduler noop registered
[17179570.580000] io scheduler anticipatory registered
[17179570.580000] io scheduler deadline registered
[17179570.580000] io scheduler cfq registered (default)
[17179570.580000] isapnp: Scanning for PnP cards...
[17179570.932000] isapnp: No Plug & Play device found
[17179570.988000] Real Time Clock Driver v1.12ac
[17179570.988000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports,
IRQ sharing enabled
[17179570.988000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179570.988000] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179570.988000] mice: PS/2 mouse device common for all mice
[17179570.988000] RAMDISK driver initialized: 16 RAM disks of 65536K
size 1024 blocksize
[17179570.988000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179570.988000] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[17179570.992000] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[17179570.992000] PNP: PS/2 controller doesn't have AUX irq; using
default 12
[17179570.992000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179570.992000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179570.992000] EISA: Probing bus 0 at eisa.0
[17179570.992000] EISA: Detected 0 cards.
[17179570.992000] TCP bic registered
[17179570.992000] NET: Registered protocol family 1
[17179570.992000] NET: Registered protocol family 8
[17179570.992000] NET: Registered protocol family 20
[17179570.992000] Using IPI No-Shortcut mode
[17179570.992000] ACPI: (supports S0 S1 S3 S4 S5)
[17179570.992000] Freeing unused kernel memory: 308k freed
[17179571.060000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179572.140000] Capability LSM initialized
[17179572.188000] ACPI Error (psparse-0537): Method parse/execution
failed [\_PR_.CPU1._PDC] (Node dffed89c), AE_BAD_HEADER
[17179572.188000] ACPI: Processor [CPU1] (supports 8 throttling states)
[17179572.188000] ACPI Exception (acpi_processor-0693): AE_NOT_FOUND,
Processor Device is not present [20060707]
[17179572.188000] ACPI: Getting cpuindex for acpiid 0x2
[17179572.188000] ACPI Exception (acpi_processor-0693): AE_NOT_FOUND,
Processor Device is not present [20060707]
[17179572.188000] ACPI: Getting cpuindex for acpiid 0x3
[17179572.188000] ACPI Exception (acpi_processor-0693): AE_NOT_FOUND,
Processor Device is not present [20060707]
[17179572.188000] ACPI: Getting cpuindex for acpiid 0x4
[17179572.828000] ICH5: IDE controller at PCI slot 0000:00:1f.1
[17179572.828000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level,
low) -> IRQ 169
[17179572.828000] ICH5: chipset revision 2
[17179572.828000] ICH5: not 100% native mode: will probe irqs later
[17179572.828000] ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings:
hda:DMA, hdb:DMA
[17179572.828000] ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings:
hdc:DMA, hdd:pio
[17179572.828000] Probing IDE interface ide0...
[17179573.124000] hda: Hitachi HDS721616PLAT80, ATA DISK drive
[17179573.576000] hdb: TSSTcorpCD/DVDW SH-S182M, ATAPI CD/DVD-ROM drive
[17179573.636000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179573.644000] Probing IDE interface ide1...
[17179573.936000] hdc: SAMSUNG SP0842N, ATA DISK drive
[17179574.644000] ide1 at 0x170-0x177,0x376 on irq 15
[17179574.676000] hda: max request size: 512KiB
[17179574.692000] hda: 321672960 sectors (164696 MB) w/7384KiB Cache,
CHS=20023/255/63, UDMA(33)
[17179574.692000] hda: cache flushes supported
[17179574.692000] hda: hda1 hda2 < hda5 >
[17179574.708000] hdc: max request size: 512KiB
[17179574.708000] hdc: 156301488 sectors (80026 MB) w/2048KiB Cache,
CHS=16383/255/63, UDMA(33)
[17179574.708000] hdc: cache flushes supported
[17179574.708000] hdc:<6>hdb: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW
drive, 2048kB Cache, UDMA(33)
[17179574.716000] Uniform CD-ROM driver Revision: 3.20
[17179574.732000] hdc1 hdc2 < hdc5 hdc6 >
[17179575.156000] usbcore: registered new driver usbfs
[17179575.156000] usbcore: registered new driver hub
[17179575.156000] USB Universal Host Controller Interface driver v3.0
[17179575.156000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level,
low) -> IRQ 177
[17179575.156000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[17179575.156000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[17179575.156000] uhci_hcd 0000:00:1d.0: new USB bus registered,
assigned bus number 1
[17179575.156000] uhci_hcd 0000:00:1d.0: irq 177, io base 0x0000dc00
[17179575.156000] usb usb1: configuration #1 chosen from 1 choice
[17179575.156000] hub 1-0:1.0: USB hub found
[17179575.156000] hub 1-0:1.0: 2 ports detected
[17179575.248000] ieee1394: Initialized config rom entry `ip1394'
[17179575.264000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level,
low) -> IRQ 185
[17179575.264000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[17179575.264000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[17179575.264000] uhci_hcd 0000:00:1d.1: new USB bus registered,
assigned bus number 2
[17179575.264000] uhci_hcd 0000:00:1d.1: irq 185, io base 0x0000e000
[17179575.264000] usb usb2: configuration #1 chosen from 1 choice
[17179575.264000] hub 2-0:1.0: USB hub found
[17179575.264000] hub 2-0:1.0: 2 ports detected
[17179575.372000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> IRQ 169
[17179575.372000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[17179575.372000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[17179575.372000] uhci_hcd 0000:00:1d.2: new USB bus registered,
assigned bus number 3
[17179575.372000] uhci_hcd 0000:00:1d.2: irq 169, io base 0x0000e400
[17179575.372000] usb usb3: configuration #1 chosen from 1 choice
[17179575.372000] hub 3-0:1.0: USB hub found
[17179575.372000] hub 3-0:1.0: 2 ports detected
[17179575.480000] ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level,
low) -> IRQ 177
[17179575.480000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[17179575.480000] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[17179575.480000] uhci_hcd 0000:00:1d.3: new USB bus registered,
assigned bus number 4
[17179575.480000] uhci_hcd 0000:00:1d.3: irq 177, io base 0x0000e800
[17179575.480000] usb usb4: configuration #1 chosen from 1 choice
[17179575.480000] hub 4-0:1.0: USB hub found
[17179575.480000] hub 4-0:1.0: 2 ports detected
[17179575.588000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 21 (level,
low) -> IRQ 193
[17179575.588000] PCI: Via IRQ fixup for 0000:01:00.0, from 10 to 1
[17179575.588000] uhci_hcd 0000:01:00.0: UHCI Host Controller
[17179575.588000] uhci_hcd 0000:01:00.0: new USB bus registered,
assigned bus number 5
[17179575.588000] uhci_hcd 0000:01:00.0: irq 193, io base 0x0000b800
[17179575.588000] usb usb5: configuration #1 chosen from 1 choice
[17179575.588000] hub 5-0:1.0: USB hub found
[17179575.588000] hub 5-0:1.0: 2 ports detected
[17179575.588000] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level,
low) -> IRQ 201
[17179575.588000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[17179575.588000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[17179575.696000] ACPI: PCI Interrupt 0000:01:00.1[B] -> GSI 22 (level,
low) -> IRQ 209
[17179575.696000] PCI: Via IRQ fixup for 0000:01:00.1, from 10 to 1
[17179575.696000] uhci_hcd 0000:01:00.1: UHCI Host Controller
[17179575.696000] uhci_hcd 0000:01:00.1: new USB bus registered,
assigned bus number 6
[17179575.696000] uhci_hcd 0000:01:00.1: irq 209, io base 0x0000bc00
[17179575.696000] usb usb6: configuration #1 chosen from 1 choice
[17179575.696000] hub 6-0:1.0: USB hub found
[17179575.696000] hub 6-0:1.0: 2 ports detected
[17179575.720000] usb 3-1: new low speed USB device using uhci_hcd and
address 2
[17179575.804000] ehci_hcd 0000:00:1d.7: new USB bus registered,
assigned bus number 7
[17179575.804000] ehci_hcd 0000:00:1d.7: debug port 1
[17179575.804000] PCI: cache line size of 128 is not supported by device
0000:00:1d.7
[17179575.804000] ehci_hcd 0000:00:1d.7: irq 201, io mem 0xff27fc00
[17179575.808000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[17179575.808000] usb usb7: configuration #1 chosen from 1 choice
[17179575.808000] hub 7-0:1.0: USB hub found
[17179575.808000] hub 7-0:1.0: 8 ports detected
[17179575.916000] ACPI: PCI Interrupt 0000:01:00.2[C] -> GSI 23 (level,
low) -> IRQ 201
[17179575.916000] PCI: Via IRQ fixup for 0000:01:00.2, from 11 to 9
[17179575.916000] ehci_hcd 0000:01:00.2: EHCI Host Controller
[17179575.916000] ehci_hcd 0000:01:00.2: new USB bus registered,
assigned bus number 8
[17179575.916000] ehci_hcd 0000:01:00.2: irq 201, io mem 0xff0fec00
[17179575.916000] ehci_hcd 0000:01:00.2: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[17179575.916000] usb usb8: configuration #1 chosen from 1 choice
[17179575.916000] hub 8-0:1.0: USB hub found
[17179575.916000] hub 8-0:1.0: 4 ports detected
[17179576.024000] ACPI: PCI Interrupt 0000:01:00.3[A] -> GSI 21 (level,
low) -> IRQ 193
[17179576.076000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[193]
MMIO=[ff0ff000-ff0ff7ff] Max Packet=[2048] IR/IT contexts=[4/4]
[17179576.148000] Attempting manual resume
[17179576.184000] kjournald starting. Commit interval 5 seconds
[17179576.184000] EXT3-fs: mounted filesystem with ordered data mode.
[17179576.284000] usb 3-1: device not accepting address 2, error -71
[17179577.364000] ieee1394: Host added: ID:BUS[0-00:1023]
GUID[00004c0107007704]
[17179577.464000] usb 3-1: new low speed USB device using uhci_hcd and
address 4
[17179577.652000] usb 3-1: configuration #1 chosen from 1 choice
[17179577.908000] usb 6-1: new full speed USB device using uhci_hcd and
address 2
[17179578.088000] usb 6-1: configuration #1 chosen from 1 choice
[17179578.092000] hub 6-1:1.0: USB hub found
[17179578.092000] hub 6-1:1.0: 4 ports detected
[17179586.432000] Floppy drive(s): fd0 is 1.44M
[17179586.560000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179586.564000] shpchp: Standard Hot Plug PCI Controller Driver
version: 0.4
[17179586.600000] Linux agpgart interface v0.101 (c) Dave Jones
[17179586.604000] agpgart: Detected an Intel 865 Chipset.
[17179586.604000] agpgart: Detected 8060K stolen memory.
[17179586.620000] agpgart: AGP aperture is 128M @ 0xf0000000
[17179586.632000] hw_random: RNG not detected
[17179586.644000] FDC 0 is a post-1991 82077
[17179586.772000] input: PC Speaker as /class/input/input1
[17179586.956000] parport: PnPBIOS parport detected.
[17179586.956000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
[17179587.704000] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level,
low) -> IRQ 217
[17179587.704000] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[17179587.732000] usbcore: registered new driver hiddev
[17179587.752000] input: Logitech USB Receiver as /class/input/input2
[17179587.752000] input: USB HID v1.11 Mouse [Logitech USB Receiver] on
usb-0000:00:1d.2-1
[17179587.784000] 8139too Fast Ethernet driver 0.9.27
[17179587.788000] input: Logitech USB Receiver as /class/input/input3
[17179587.788000] input,hiddev96: USB HID v1.11 Device [Logitech USB
Receiver] on usb-0000:00:1d.2-1
[17179587.788000] usbcore: registered new driver usbhid
[17179587.788000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[17179587.948000] ts: Compaq touchscreen protocol output
[17179588.024000] intel8x0_measure_ac97_clock: measured 59675 usecs
[17179588.024000] intel8x0: clocking to 48000
[17179588.048000] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 22 (level,
low) -> IRQ 209
[17179588.048000] eth0: RealTek RTL8139 at 0xf8978800,
00:13:8f:cf:d6:06, IRQ 209
[17179588.048000] eth0: Identified 8139 chip type 'RTL-8101'
[17179588.072000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[17179588.208000] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[17179588.308000] lp0: using parport0 (interrupt-driven).
[17179588.352000] SCSI subsystem initialized
[17179588.360000] ieee1394: sbp2: Driver forced to serialize I/O
(serialize_io=1)
[17179588.360000] ieee1394: sbp2: Try serialize_io=0 for better performance
[17179588.400000] Adding 1124508k swap on
/dev/disk/by-uuid/5897b64e-5677-4d9b-9b23-8bc29e9a81ee. Priority:-1
extents:1 across:1124508k
[17179588.592000] EXT3 FS on hdc6, internal journal
[17179589.276000] NET: Registered protocol family 17
[17179591.016000] NET: Registered protocol family 10
[17179591.016000] lo: Disabled Privacy Extensions
[17179591.016000] IPv6 over IPv4 tunneling driver
[17179597.284000] NTFS driver 2.1.27 [Flags: R/O MODULE].
[17179597.340000] NTFS volume version 3.1.
[17179597.432000] kjournald starting. Commit interval 5 seconds
[17179597.440000] EXT3 FS on hdc1, internal journal
[17179597.440000] EXT3-fs: mounted filesystem with ordered data mode.
[17179601.160000] eth0: no IPv6 routers present
[17179603.112000] ACPI: Power Button (FF) [PWRF]
[17179603.112000] ACPI: Power Button (CM) [PWRB]
[17179603.256000] ibm_acpi: ec object not found
[17179603.284000] pcc_acpi: loading...
[17179605.668000] [drm] Initialized drm 1.0.1 20051102
[17179605.672000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level,
low) -> IRQ 177
[17179605.672000] [drm] Initialized i915 1.5.0 20060119 on minor 0
[17179607.156000] apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
[17179607.156000] apm: overridden by ACPI.
[17179612.004000] Bluetooth: Core ver 2.8
[17179612.004000] NET: Registered protocol family 31
[17179612.004000] Bluetooth: HCI device and connection manager initialized
[17179612.004000] Bluetooth: HCI socket layer initialized
[17179612.052000] Bluetooth: L2CAP ver 2.8
[17179612.052000] Bluetooth: L2CAP socket layer initialized
[17179612.068000] Bluetooth: RFCOMM socket layer initialized
[17179612.068000] Bluetooth: RFCOMM TTY layer initialized
[17179612.068000] Bluetooth: RFCOMM ver 1.7
[17179642.652000] usb 6-1.2: new full speed USB device using uhci_hcd
and address 3
[17179642.760000] usb 6-1.2: not running at top speed; connect to a high
speed hub
[17179642.792000] usb 6-1.2: configuration #1 chosen from 1 choice
hans@hans-desktop$

---

Lasse Jensen skrev:
En grim måde, der måske kan hjælpe er at køre
> killall hald som root og prøve igen. Så vil den dog ikke selv poppe op, men
> du vil kunne se den med lsusb og dmesg. Jeg har været ude for en USB
> lagerenhed der ikke kunne sammen med HAL og crashede når den blev
> tilsluttet. Genstart maskinen bagefter, så du er sikker på at virker som
> det skal.


Inden jeg forsøger dette, må jeg lige vide, hvad jeg risikerer. "killall
hald"?

Hans

---

Den Thu, 10 Jan 2008 20:54:58 +0100 skrev Hans Houmøller:
> Lasse Jensen skrev:
> En grim måde, der måske kan hjælpe er at køre
>> killall hald som root og prøve igen. Så vil den dog ikke selv poppe op, men
>> du vil kunne se den med lsusb og dmesg. Jeg har været ude for en USB
>> lagerenhed der ikke kunne sammen med HAL og crashede når den blev
>> tilsluttet. Genstart maskinen bagefter, så du er sikker på at virker som
>> det skal.
>
>
> Inden jeg forsøger dette, må jeg lige vide, hvad jeg risikerer. "killall
> hald"?

At skulle genstarte bagefter.

Mvh
Kent
--
"So there I was surrounded by all these scary creatures
They were even scarier than what Microsoft call features"
- C64Mafia: Forbidden Forest (Don't Go Walking Slow).

---

Hans Houmøller wrote:

> Lasse Jensen skrev:
> En grim måde, der måske kan hjælpe er at køre
>> killall hald som root og prøve igen. Så vil den dog ikke selv poppe op,
>> men du vil kunne se den med lsusb og dmesg. Jeg har været ude for en USB
>> lagerenhed der ikke kunne sammen med HAL og crashede når den blev
>> tilsluttet. Genstart maskinen bagefter, så du er sikker på at virker som
>> det skal.
>
>
> Inden jeg forsøger dette, må jeg lige vide, hvad jeg risikerer. "killall
> hald"?

http://www.freedesktop.org/wiki/Software/hal

Som jeg har forstået det er det et forsøg på at få Linux til at ligne
Windows.

Men udfra det du poster vil du nok hellere se på
http://libmtp.sourceforge.net/

--
Lasse Jensen [fafler at g mail dot com]
Linux, the choice of a GNU generation.

---

Lasse Jensen wrote:

> Som jeg har forstået det er det et forsøg på at få Linux til at ligne
> Windows.

Det er en måde at lette portabilitet mellem forskellige hardwareplatforme.


--
Mvh
Jesper Poulsen

---

Jeg har løst problemet lidt ved at skifte min lidt obskure WinXP ud med
en licenceret udgave. Det betyder, at jeg kan bruge min mp3 på min egen pc.
Så mangler jeg bare at få den til at virke under ubuntu!
Tak for rigtig mange venlige og gode svar!!!
Hans

---

Hans Houmøller <hanshoumoller@mail.dk> writes:

> Jeg har anskaffet en Samsung (YP-K3) mp3-afspiller, som jeg ikke kan
> få til at virke i ubuntu. den kan køre på husets anden pc (WinXP) og
> virker helt der.
> Min ubuntu kan ikke se den overhovedet.
> Kan nogen her hjælpe?
> Hans


Et par links:
http://ubuntuforums.org/showthread.php?t=429935
http://gentoo-wiki.com/HARDWARE_Samsung_K3


mvh Ian

---

Jeg har nu fået hul igennem til mp3'eren af flere veje:
1) jeg opgraderede min WinXP til WinVista, hvor den kører uden problemer
2) jeg gik fra ubuntu 6.10 til 7.10, hvor der viste sig muligheder
(efter en del søgen rundt), som gør at jeg nu kan hente podcasts til
afspilleren. Jeg bruger Amarok.
De første gange meldte Amarok fejl ved "automontering af deveice", men
jeg søgte i Synaptic på "mp3" og "podcast" og fandt nogle ting, der fik
det til at virke.
Atter må jeg sige tak for god og gidende assist til i dett forum til en
ældre herre.
Hans