Hej NG
Har lige installeret FreeBSD 4.5 igen...Hvis jeg forsøger at logge ind via
SSH på min server(FreeBSD) bruger den meget lang tid på at logge ind,
omkring 1 minut...Jeg kan ikke lige gennemskue hvad der er galt...lidt info
om maskinen..
Asus P2B-F m celeron 300a
netkort Olicom 2326 med TI chip(bruger tl driveren)
sådan ser min /var/run/dmesg.boot ud:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-RELEASE #0: Mon Jan 28 14:31:56 GMT 2002
murray@builder.freebsdmall.com:/usr/src/sys/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (300.68-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x665 Stepping = 5
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,
PA
T,PSE36,MMX,FXSR>
real memory = 67096576 (65524K bytes)
avail memory = 60641280 (59220K bytes)
Preloaded elf kernel "kernel" at 0xc0496000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 7 entries at 0xc00f0d10
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <S3 Trio3D/2X graphics accelerator> at 0.0
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xd800-0xd80f at device 4.1 on
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f at
device 4.
2 on pci0
pci_cfgintr_search: linked (63) to configured irq 10 at 0:10:0
pci_cfgintr: 0:4 INTD routed to irq 10
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at
device
4.3 on pci0
tl0: <Olicom OC-2326 10/100 TX UTP> port 0xd000-0xd00f mem
0xdb800000-0xdb80000f
irq 10 at device 10.0 on pci0
tl0: Ethernet address: 00:00:24:28:c7:41
miibus0: <MII bus> on tl0
mlphy0: <Micro Linear 6692 media interface> on miibus0
mlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlphy0: <ThunderLAN 10baseT media interface> on miibus0
tlphy0: 10base2/BNC, 10base5/AUI
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xb800-0xb8ff mem
0xdb000000-0xdb00
0fff irq 11 at device 11.0 on pci0
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/255 SCBs
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcc7ff on isa0
fdc0: direction bit not set
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: parallel port not found.
acd0: CDROM <WEARNES CDD-120> at ata0-slave using PIO0
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da1 at ahc0 bus 0 target 1 lun 0
da1: <IBM DCAS-34330 !# S69D> Fixed Direct Access SCSI-2 device
da1: 10.000MB/s transfers (10.000MHz, offset 15)
da1: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
da0 at ahc0 bus 0 target 0 lun 0
da0: <IBM DCAS-34330 !# S69D> Fixed Direct Access SCSI-2 device
da0: 10.000MB/s transfers (10.000MHz, offset 15)
da0: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
hvis i skal have mere information så bare skriv hvor jeg skal finde
det...havde det samme problem, derfor reinstallerede jeg.
mvh.
Martin Søndergård