/ Forside / Teknologi / Internet / Sikkerhed / Nyhedsindlæg
Login
Glemt dit kodeord?
Brugernavn

Kodeord


Reklame
Top 10 brugere
Sikkerhed
#NavnPoint
stl_s 37026
arlet 26827
miritdk 20260
o.v.n. 12167
als 8951
refi 8694
tedd 8272
BjarneD 7338
Klaudi 7257
10  molokyle 6481
Hvordan resetter jeg en firebox II
Fra : AR


Dato : 15-10-02 03:32

Hej NG,

Hvordan resetter jeg en firebox II, jeg har fået den fra et konkurs bo, og
har derfor intet dokumentation, jeg synes ikke at kunne få hul igemmen via
serial porten! På firebox III er der en reset knap på bagsiden men ikke på
v. II.

Hilsen Allan





 
 
Ole Thomsen (15-10-2002)
Kommentar
Fra : Ole Thomsen


Dato : 15-10-02 14:23

"AR" <allan@asp-host.dk> wrote
>
> Hvordan resetter jeg en firebox II, jeg har fået den fra et konkurs bo, og
> har derfor intet dokumentation, jeg synes ikke at kunne få hul igemmen via
> serial porten! På firebox III er der en reset knap på bagsiden men ikke på
> v. II

The Firebox can boot from the primary area of the flash disk (Sys A) in a mode
that provides fail-safe access in cases when you need to:
a.. Install a Firebox for the first time
b.. Troubleshoot problems in which all access to the Firebox is lost
c.. Reset Firebox passphrases when you do not know or have forgotten them
This Enhanced System Mode is the default mode for new Fireboxes shipped from
the factory. If a Firebox is in this mode, its Sys A light blinks. A Firebox
can also be placed into Enhanced System Mode by connecting any two of the
Firebox Ethernet interfaces in a loopback configuration. Use a red crossover
cable included with the Firebox for this purpose.

To access a Firebox in Enhanced System Mode:

1.. Establish a physical Ethernet connection between the Trusted interface of
the Firebox and the Management Station on the same segment.
2.. Attach the red crossover cable between the remaining two Firebox
interfaces, and then turn the power on the Firebox off and then on. If a small,
"factory default" switch is present on the rear of the Firebox, press and hold
that switch while you turn the Firebox power off and then on.
The Firebox boots into the Enhanced System Mode. This is indicated by a
blinking Sys A light.
3.. Reinitialize the Firebox using the QuickSetup Wizard.
For more information on the QuickSetup Wizard, see the Quick Start Poster.
4.. When you complete the QuickSetup Wizard, remove the loopback cable
(assuming your Firebox has one) and return the Firebox to its regular position
in your network. The Firebox resumes normal operation the next time it
restarts.
Ole Thomsen




AR (15-10-2002)
Kommentar
Fra : AR


Dato : 15-10-02 21:54

Så siger jeg bare tak ./


"Ole Thomsen" <ot@networks.dk> wrote in message
news:3dac16a3$1@mail.ehs.dk...
> "AR" <allan@asp-host.dk> wrote
> >
> > Hvordan resetter jeg en firebox II, jeg har fået den fra et konkurs bo,
og
> > har derfor intet dokumentation, jeg synes ikke at kunne få hul igemmen
via
> > serial porten! På firebox III er der en reset knap på bagsiden men ikke

> > v. II




Søg
Reklame
Statistik
Spørgsmål : 177549
Tips : 31968
Nyheder : 719565
Indlæg : 6408820
Brugere : 218887

Månedens bedste
Årets bedste
Sidste års bedste